Couple of questions

technical support and information on EMC topcoats and coatings
User avatar
Cracker Larry
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 22491
Joined: Fri Mar 11, 2005 3:39 pm
Location: Savannah, GA

Couple of questions

Post by Cracker Larry »

How long should I let S3 primer cure before covering it with EMC primer?

How long should the EMC primer cure before top coating?

What type of roller do you recommend for the EMC top coats?

Thanks!
Completed GF12 X 2, GF16, OD18, FS18, GF5, GF18, CL6
"Ships are the nearest things to dreams that hands have ever made." -Robert N. Rose

User avatar
Cracker Larry
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 22491
Joined: Fri Mar 11, 2005 3:39 pm
Location: Savannah, GA

Re: Couple of questions

Post by Cracker Larry »

Bump?
Completed GF12 X 2, GF16, OD18, FS18, GF5, GF18, CL6
"Ships are the nearest things to dreams that hands have ever made." -Robert N. Rose

User avatar
tech_support
Very Active Poster
Very Active Poster
Posts: 12318
Joined: Wed Dec 31, 1969 7:00 pm
Location: Vero Beach, FL
Contact:

Re: Couple of questions

Post by tech_support »

How long should I let S3 primer cure before covering it with EMC primer?
I would wait the same time you would wait for topcoat. At least a few days so all the water evaporates out of the S3.
How long should the EMC primer cure before top coating?
On a thin coat, I have gone next day, but its probably a good idea to wait two

Data sheet says full cure in 72 hours. There is a link to the data sheet here...

http://boatbuildercentral.com/proddetai ... SP_GRAY_QT
What type of roller do you recommend for the EMC top coats?
I used the same West System style 1/4" foam nap. You can roll it on a good bit heavier than the Sterling.

User avatar
Cracker Larry
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 22491
Joined: Fri Mar 11, 2005 3:39 pm
Location: Savannah, GA

Re: Couple of questions

Post by Cracker Larry »

Thanks Joel.
I would wait the same time you would wait for topcoat. At least a few days so all the water evaporates out of the S3.
Not the answer I was hoping for, but the one I expected. Just finished the last coat of S3 this afternoon and was hoping to keep moving with the EMC tomorrow. Oh well, I reckon it's time to pull the engine off the Parker and get something done there for a few days.
Completed GF12 X 2, GF16, OD18, FS18, GF5, GF18, CL6
"Ships are the nearest things to dreams that hands have ever made." -Robert N. Rose

User avatar
tech_support
Very Active Poster
Very Active Poster
Posts: 12318
Joined: Wed Dec 31, 1969 7:00 pm
Location: Vero Beach, FL
Contact:

Re: Couple of questions

Post by tech_support »

sorry larry :|

User avatar
Cracker Larry
* Bateau Builder - Expert *
* Bateau Builder - Expert *
Posts: 22491
Joined: Fri Mar 11, 2005 3:39 pm
Location: Savannah, GA

Re: Couple of questions

Post by Cracker Larry »

Needed a painting break anyway 8) I'd rather be safe than have a problem later.
Completed GF12 X 2, GF16, OD18, FS18, GF5, GF18, CL6
"Ships are the nearest things to dreams that hands have ever made." -Robert N. Rose

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests